User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            Tektronix 2440:Digital Oscilloscope
DATE:                  30-Oct-97
AUTHOR:                User Contributed
REVISION:              0
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       81
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  IEEE         [SRQ OFF]
# 1.002  IEEE         [@2465]INIT SRQ
  1.002  HEAD         Preliminary Procedure
  1.003  DISP         Connect the UUT IEEE cable to the Tektronix 2440
  1.003  DISP         Oscilloscope IEEE connector.
  1.004  DISP         1- Turn the UUT on.
  1.004  DISP         2- Press the OUTPUT button.
  1.004  DISP         3- Press the SETUP button.
  1.004  DISP         4- Press the MODE button and then the T/L button.
  1.005  DISP         1- Press the OUTPUT button.
  1.005  DISP         2- Press the SETUP button
  1.005  DISP         3- Press the TERM button and then the LF/EOI button.
  1.006  DISP         1- Press the OUTPUT button.
  1.006  DISP         2- Press the SETUP button
  1.006  DISP         3- Press the ADDR button and then [27][91]1mcheck
  1.006  DISP         [32]  that the GPIB ADDRESS =  any number but "0".
  1.007  DISP         1- Press the MENU OFF / EXTENDED FUNCTIONS button.
  1.007  DISP         2- Press SYSTEM softkey.
  1.007  DISP         3- Press MISC softkey.
  1.007  DISP         4- Verify that TRIG T is ON. (If not select on)
  1.008  DISP         This instrument must be powered up for at least 20
  1.008  DISP         minutes before performance requirements can be checked.
  1.009  DISP         To verify that the UUT is warm or not, press the UUT
  1.009  DISP         MENU OFF/EXTENDED FUNCTIONS pushbutton (front panel next
  1.009  DISP         to POWER button). Then press CAL/DIAG soft key. If the
  1.009  DISP         message NOT WARMED UP is displayed
  1.009  DISP         do not continue until message clears.
  1.009  DISP
  1.009  DISP         When UUT is ready press ADV to initiate SELF CAL.
  1.010  HEAD         SELF CAL in progress....
  1.011  MATH         MEM = 0
  1.012  IEEE         [TERM LF]
  1.013  IEEE         MENUOFF
  1.014  IEEE         MESS 1: "SELF CAL IN PROGRESS...."
  1.015  IEEE         OPC ON
  1.015  IEEE         TESTTYPE SELFCAL
  1.015  IEEE         EXECUTE
  1.016  IEEE         [D2000] [SPL]
  1.017  MATH         MEM = MEM - 1
  1.018  MEME
  1.019  JMPZ         1.021          2U
  1.020  JMP          1.016
  1.021  HEAD         SELF CAL PASSED
  1.022  IEEE         MENUOFF [D2000]
# 1.023  CALL         Tektronix 2440 Sub1
  1.023  CALL         Tektronix 2440 Sub2
  1.024  CALL         Tektronix 2440 Sub3
  1.025  CALL         Tektronix 2440 Sub4
  1.026  CALL         Tektronix 2440 Sub5
  1.027  CALL         Tektronix 2440 Sub6
  1.028  CALL         Tektronix 2440 Sub7
  1.029  CALL         Tektronix 2440 Sub8
  1.030  CALL         Tektronix 2440 Sub9
  1.031  CALL         Tektronix 2440 Sub10
  1.032  CALL         Tektronix 2440 Sub11
  1.033  CALL         Tektronix 2440 Sub12
  1.034  CALL         Tektronix 2440 Sub13
  1.035  CALL         Tektronix 2440 Sub14
  1.036  CALL         Tektronix 2440 Sub15
  1.037  CALL         Tektronix 2440 Sub16
  1.038  CALL         Tektronix 2440 Sub17
  1.039  CALL         Tektronix 2440 Sub18
  1.040  CALL         Tektronix 2440 Sub19
  1.041  CALL         Tektronix 2440 Sub20
  1.042  CALL         Tektronix 2440 Sub21
  1.043  CALL         Tektronix 2440 Sub22
  1.044  CALL         Tektronix 2440 Sub23
  1.045  CALL         Tektronix 2440 Sub24
  1.046  CALL         Tektronix 2440 Sub25
  1.047  END